Results 1 to 4 of 4

Thread: 2008 Black SX4 Turbo 5MT

  1. #1
    Join Date
    Nov 2010
    Location
    San Antonio, TX
    Posts
    2,842

    2008 Black SX4 Turbo 5MT

    A piece of SX4 history is available for purchase. There are many rare and discontinued parts included in this sale. Photos documenting the majority of the build are available at https://www.flickr.com/photos/44381367@N07/.


    Not willing to part anything out and want to sell altogether.


    Overview
    2008 Black Suzuki SX4 Turbo with FlexFuel (runs on gasoline and any blend of gasoline and ethanol up to E85)
    5 Speed MT with 2007 5th gear
    360 WHP / 370 TQ at 26 PSI
    Located in San Antonio, TX
    113,000 miles
    Listed $16,000 USD
    DM with questions/inquiries



    Engine Under 500 miles / Break in oil drained and replaced with fresh oil.
    Professionally built engine from Performance Race Engineering in Portland, OR
    Darton M.I.D. Sleeves
    Pauter Rods
    Manley Pistons
    ARP Head Studs
    Light porting of the head
    Fire rings installed in head
    Garrett GT2876R Gen II Turbo with Stainless Tial .64 A/R Turbine Housing T51R mod compressor housing installed (original is included)
    Black satin ceramic coated stainless manifold, downpipe, and turbine housing
    Full 3 exhaust with new high flow catalytic converter
    Aluminum intercooler piping
    The manifold, downpipe, exhaust, and intercooler piping were from K-9s Zukzilla build
    DEI Titanium wrapped turbo manifold, turbine housing, and down pipes
    Treadstone TR8L Intercooler
    Tial MV-S Wastegate
    Tial Q 50mm BOV
    Oil pan outside coated in thermal dispersant and inside coated with oil shedding compound
    Stainless Steel Braided Radiator hoses
    Treadstone Stainless Turbo Coolant lines
    B&M Supercooler 70273 Oil Cooler
    Improved Racing 215 degree (F) Oil Thermostat
    Blox Oil Filter Relocation Kit with Braided hoses and AN fittings


    Electronics
    Split Second CEL Eliminator
    Haltech Elite 1500 wired into test/jumper harness. (Tuning performed by Performance Race Engineering in Portland, OR)
    Haltech Version of the Racepak IQ3 Dash
    Haltech Wideband
    Haltech Thermocouple
    Haltech Can Hub


    Suspension
    KSport (RR Version) Coilovers
    Progress Technology Front (25.5mm) and Rear Sway Bar
    Ultra Racing Rear Strut Bar
    Rocky Road Outfitters shock relocation kit


    Brakes
    Rotora 330mm Super Challenge BBK
    StopTech Sport Slotted Rear Rotors
    Techna-Fit Stainless Brake Lines


    Fuel
    Radium Engineering Fuel Surge Tank with Dual Bosch 044 fuel pumps
    PTFE hoses with Red Horse hose fittings
    Flex Fuel Sensor
    1200cc WRX (02-14)/STI(07+) Fuel Injector Clinic injectors


    Exterior
    Joey Mod w/ Morimoto Mini H1 6.0 projector retrofit including 3Five 5K bulb, Denso Slim Ballasts (waterproofed), E46-R extended shrouds, and MotoControl Bixenon 9007/9004 harness. (DRL disabled)
    Small hexagon mesh used to cover front bumper openings
    Debadged and silver accent trim removed
    Shaved roof mounts
    RRP Rear Wiper Delete
    Audi TT Mk1 antenna delete plug
    Red Smoke LED Tinted Tail Lights
    18x7.5 ET 40mm Volk TE-37 Wheels
    225/40/18 Bridgestone RE-71R
    Volk Rays Black Clubsport wheel center caps


    Interior
    Carpet, interior panels, and seats are currently installed in the car
    RaceTech RT4009W Bucket Seat
    Racetech seat brackets
    Planted seat bracket
    Sparco 04837RHRS 6Point P-3 Hans Formula Belt
    White Beatrush Duracon Shift Knob Style A
    Suzuki Sport Aluminum Pedals
    Volanti Luisi Steering Wheel Hub Adapter
    Sparco 383 suede steering wheel Carbon fiber wrapped radio trim panels
    NRG Quick Release Steering wheel
    Center Panel Box Cover from overseas
    Seatbelt harness bar
    JDM sun visors
    Laile-Beatrush Quick Shift Control (Short Shift Kit)


    Other
    Tinted windows
    Perma-Cool 19122 12 aluminum fan
    Hella Supertones
    Beatrush Alternator Pulley
    OBX Underdrive Pulley
    Clutch Masters FX400 Clutch Kit - 04109-HDCL
    ARP M16A Flywheel Bolt Kit
    ARP Extended Wheel Studs (12mm x 1.50) - ARP part number 100-7712
    RRP Steering Low-Position Spacer
    Reinforced Polyurethane Engine/Transmission Mounts
    Rennline universal tow hook receiver, stainless steel folding tow hook, screw in license plate frame
    Urethane Exhaust Hanger Bushings
    Odyssey Battery HK-PC680 Hold Down Kit.
    New radiator, water pump, alternator, battery,


    Additional Parts included
    BoSpeed Carbon Fiber Vented Hood
    Ducks-Garden Fiberglass Front Bumper
    RRM/Carbon Trix Carbon Fiber Front Bumper (Upper part near grill in need of repair)
    Carbon Fiber Rear Spoiler
    DCCD AWD controller
    ClutchNet clutch kit with higher clamping force pressure plate, 6 button sprung hub clutch disc, throwout bearing, and alignment tool.
    2 spare throw out bearings
    Spare engine block, head, transmission (original with taller 5th gear) and transfer
    Dynotronics Reflashed ECU (Throttle Fix, 8000 RPM limit, speed governor removed)
    Beatrush QSC Knob
    AEM F/IC 6 wired into test/jumper harness
    Aquamist WMI system with 2 gallon Howerton Engineering tank
    Shift-I sequential shift light
    Custom battery catch-can and overflow tank from K-9s build
    WC Lathe Werks WRX 9" Bent Lever Extension with a Double Bend
    K&N Air Filters in different sizes
    Extra intercooler piping
    Complete Suzuki Tappet Shim Kit
    Printed Service Manual
    All original parts plus a variety of other components collected over the years

  2. #2
    Join Date
    Apr 2013
    Location
    Sherbrooke, Quebec, Canada
    Posts
    1,899
    By far the best sx4 on the planet. Completely maxed out at every level....

    What are your plans for the future?

    I would have taken this in a heartbeat... it's such a tough process building these cars... but the end result is out of this world...
    AWD 2013. CVT. Beast (RIP 2019)
    AWD 2013 6 speed Monster (stay tuned)

  3. #3
    Join Date
    Nov 2010
    Location
    San Antonio, TX
    Posts
    2,842
    Thanks Samus. Appreciate the support. No car projects planned in the near future. I'm in process of building a house which is tying up funds. Work and raising a family is occupying the majority of my time so unfortunately no time to enjoy the build.

  4. #4
    Join Date
    Apr 2013
    Location
    Sherbrooke, Quebec, Canada
    Posts
    1,899
    I hear ya. I'm in the same boat. Built this nice sx4 and can barely drive it once a week.... my 15 month son is my new priority.
    AWD 2013. CVT. Beast (RIP 2019)
    AWD 2013 6 speed Monster (stay tuned)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •